Orders >$15 will ship with full tracking from the US to domestic destinations and USPS ePacket countries (most of Europe, Brazil, Russia, Japan, South Korea, Singapore, Hong Kong, Israel, Australia, New Zealand).

Autolight-board
Board Name:
Dimensions:
Price:
Total Cost:

Created by NStorm on 2019-05-28 10:01:54

Description: # Auto light
Attiny10 & APDS-9930 based automatic light/switch

https://github.com/N-Storm/autolight

https://easyeda.com/NStorm/autolight-board

This project utilizes small ATtiny10 mcu to work with APDS-9930 ambient light (AL) and proximity I2C sensor.
This is used for automatic "smart" light in a drawer. Once the drawer are open the APDS-9930 will notice proximity change
and trigger a preset interrupt and MCU will come from sleep to check if AL level are below set (i.e. it's dark around).
If the set condition for AL level will be met, it will enable HIGH level on PB3 pin. Which is connected to a MOSFET or any other switch to enable LED light.

Reset shares same PB3 pin so it must be disabled via fuses. You will have to apply +12V to PB3/RESET pin to reprogram attiny10 after flashing RSTDISBL fuse.

The PB2 port are used as INT0 for sensor interrupts to wake MCU from sleep on proximity change event.

Building

Fetch the latest trunk:

git clone https://github.com/N-Storm/autolight && cd autolight

Then tweak some settings in autolight.h if required. They are commented. After that do a:

make && make flash && make fuse.

:warning: After you do a make fuse step, you won’t be able to program MCU again without applying +12V to RESET pin (make sure it’s not connected to your programmer hardware :warning:

Alternatively you can use pre-built binaries with the default settings from releases section.

Connecting

PB0 ↔ SCL

PB1 ↔ SDA

PB2 ↔ INT

PB3 are the module digital output, with logic LOW when light should be turned off and HIGH when it should be on. Suited for connecting to an N-channel FET driving the LED light.

Please be aware that the APDS-9930 module requires 2.5 – 3.6 V for it’s operation on Vdd+Vbatt (IR LED power). I recommend to use a 3.3V LDO for powering both MCU & APDS-9930.

Schematics & board are available on EasyEDA: https://easyeda.com/NStorm/autolight-board

:warning: This board has two places for LDOs - U3 & U4. Solder only one of them! :warning:

They replace each other. The board are made so they could replace each other. Alternatively edit board/schematics to replace them with your favorite LDO.

This project utilizes software I2C library by eXtreme Electronics, India.
www.eXtremeElectronics.co.in

License: CC-BY-SA 3.0
Project URL: https://github.com/N-Storm/autolight
Board Revision: r2
Tags: avr, attiny, attiny10, light, home automation

Order Now

Board Images:

Top View - Complete Board

Top View - Complete Board

This is what your finished board will look like from the top.

Bottom View - Complete Board

Bottom View - Complete Board

This is what your finished board will look like from the bottom.

Board Outline

Board Outline

This shows the outline of your board, it will be cut to this shape.

Top Copper Layer

Top Copper Layer

This shows where the copper will remain after etching the top of the board.

Bottom Copper Layer

Bottom Copper Layer

This shows where the copper will remain after etching the bottom of the board. (mirrored)

Top Soldermask

Top Soldermask

This shows where soldermask will be applied on the top over the bare copper board.

Bottom Soldermask

Bottom Soldermask

This shows where soldermask will be applied on the bottom over the bare copper board. (mirrored)

Top Silkscreen

Top Silkscreen

This is the white print that will be printed on the top of the board.

Bottom Silkscreen

Bottom Silkscreen

This is the white print that will be printed on the bottom of the board. (mirrored)

Drill Holes

Drill Holes

This shows all the holes that will be drilled in your board.